动车组司机室空调蒸发器气动噪声数值仿真

为研究动车组司机室空调蒸发器的噪声响应，建立某型司机室分体式空调蒸发器的计算流体动力学模型，采用FLUENT中的大涡模拟（large eddy simulation, LES）计算瞬态气动流场。对瞬态流场数据进行傅里叶变换，得到空气流场的频域数据。基于流场频域数据，采用Virtual.Lab的边界元法计算蒸发器的气动噪声，采用声压法计算蒸发器的辐射声功率，并与测试结果进行对比分析。结果表明：蒸发器出口位置气动噪声最高，最大声压级高于56 dB；最大声功率级出现在125~400 Hz的低频段；声功率级随着频率的增加逐渐降低，但在5 000 Hz的高频辐射中声功率级仍然超过55 dB，这表明空调蒸发器气动噪声属于宽频噪声；计算结果与测试结果吻合良好，验证声压法计算空调蒸发器气动声功率可行。     

正偏心正交车铣精加工切削层几何形状研究

针对未考虑正偏心正交车铣切削层几何形状而导致难以全面反映正交车铣切削层几何形状变化规律的问题，基于正交车铣运动规律，在不考虑动力学影响的情况下，对切削层的形成过程进行了静态分析。建立的正偏心正交车铣切削层几何形状的解析模型涉及铣刀侧刃和底刃的切入/切出角度、切削厚度和切削深度。通过试验验证了该解析模型的正确性，并分析了切削参数对铣刀切削层的影响。研究结果为正偏心正交车铣切削层几何形状的变化提供了定量的分析依据，为切削力和颤振的研究提供了理论指导。     

Using hydroacoustics to relate fluctuations in fish abundance to river restoration efforts and environmental conditions in the Penobscot River,Maine

Quantifying change after large habitat restoration efforts is critical to assessing the effort's success. After river restoration activities, fish abundance is expected to increase and also fluctuates naturally by season and with environmental conditions. A side‐looking hydroacoustic system was used to estimate fish abundance in the Penobscot River, ME, from 2010 to 2016 during predam (2010–2013) and postdam (2014–2016) removal years during nonice periods. Automated data processing enabled continuous abundance estimates from fish tracks. A threefold increase in mean fish abundance was recorded after dam removal. A fourfold increase in median fish abundance occurred in the fall relative to spring and summer of the same year, regardless of dam presence. Interannual fish abundance in every season monitored increased at least twofold after dam removal. We related variability in fish abundance to tide, discharge, temperature, diurnal cycle, daylength, moon phase, and restoration activities (focusing on dam presence). Daylength corresponding to the fall and summer was the most important indicator for higher fish abundance. Fish abundance was generally greatest in the fall during outgoing tides at night, with lesser peaks occurring during the month of June at night. Before dam removal, fish abundance peaked when water temperature was less than 9.25°C, at night, during outgoing tides. After dam removal, fish abundance peaked when daylength was less than 11.3 hr, at night, during outgoing tides, when water temperature was above 4.56°C and no full moon was present. Peak fish abundance occurred during only 0.02–2.3% of the total time sampled. The threefold increase in fish abundance recorded after dam removal was observed despite yearly stocking efforts of adult alewife increasing 24% in postdam removal years. Finally, parallel studies of fish presence in the Penobscot River were used to compare the utility of this method as an indicator of fish abundance in response to dam removal.     

Ex post demand information sharing between differentiated suppliers and a common retailer

We consider ex post demand information sharing in a two-echelon supply chain in which two suppliers sell differentiated products through a common retailer. We model three scenarios of information sharing to characterise the conditions under which information sharing may benefit or hurt different players: (1) no supplier is informed; (2) only one supplier is informed; and (3) both suppliers are informed. We find that the retailer may voluntarily share the low demand information when the product differentiation and demand magnitude satisfy certain conditions. In contrast, the retailer has no incentive to share the high demand information, even though this information benefits the suppliers. To achieve information sharing, we propose a side payment mechanism, which allows benefitted players to subsidise hurtful players. Finally, we extend our model by considering a situation where the suppliers have limited capacity and may invest to ramp up production capacity to satisfy a high demand.     

关于硬件木马电路检测技术分析及发展趋势探讨

本文结合HTH电路的复杂性等特征分析与实际应用现状,研究了HTH电路的具体检测技术方法并对当前热点技术进行对比分析,探讨了HTH电路检测方法的技术发展趋势。     

宏阳煤矿薄煤层沿空留巷实践应用

为了缓解矿井采掘接替紧张局面,宏阳煤矿采用沿空留巷技术,对12102运输顺槽采取顶板超前采面打设锚索梁、顶板超前预裂爆破,留巷段采用“钢梁+单体液压支柱”的方式进行巷道支护。该技术现场应用后,减少了巷道掘进工程量,减少了煤炭损失,增加了经济效益,降低了职工劳动强度,有利于采掘接替。     

2195铝锂合金碱性化学铣切工艺探究

初步研究了2195铝锂合金碱性化学铣切(简称化铣)工艺。结果表明,在一定条件下,通过添加一定浓度的添加剂A、B和C,2195铝锂合金平板试片化铣均匀性好,化铣速度为0.0297mm/min,侧切率为0.988,粗糙度基本保持不变。研究结果对2195铝锂合金产品化铣加工工艺优化可提供参考。     

浅谈压延铜箔光面色差的成因

针对压延铜箔在表面处理过程中光面易出现色差的问题,从设备、工艺、人员操作等方面进行成因探讨,并给出了应对措施。     

尿素装置液位仪表失真分析及处理

介绍了尿素装置中3起液位仪表失真案例,分析了故障现象和设备工况,确定失真原因,采取了相应的处理措施,解决了仪表故障。     

基于局部分型面的电器外壳注塑模具设计

电器外壳制品形状结构复杂,有两处侧凸(孔)较难处理。通过对矩形孔内侧凸的结构分析,在其局部设计了分型面,避免了使用侧向抽芯机构;对侧孔部位设计了斜顶杆侧向抽芯机构,其结构简单、紧凑。模具采用一模二腔、平衡式布局,采用经扁推杆由制品内部进料的潜伏式浇口,S型流道。在NX 8.0中完成了模具结构设计。经实践证明,该模具结构合理,产品合格。